本文解释了您应如何配置 Cisco CME（或 CUBE）网关，以便向我们的系统发送呼叫
分步指南
首先，请从 MultiTEL 获取您的 SIP 用户名和密码。
您可以在我们的 Trunks 部分创建一对 SIP Username/Password：
https://multitel.net/trunks/accounts
您也可以在此处添加您的 IP 地址：
https://multitel.net/trunks/ips
- 登录您的 Cisco 语音网关，并使用与下方类似的配置（请根据需要修改）
完成后，请使用以下命令从 Cisco CLI 控制台测试您的呼叫：
csim start <enter_here_your_phone_number>
例如，如果您的电话号码是 18886868581，则此 CLI 命令如下所示
csim start 18886868581
此命令将从您的 Cisco 语音网关通过 MultiTEL 的终接服务发起一个电话呼叫，用于测试您的配置。
此外，您还可以随时使用以下两个命令：
show call active voice brief
show call history voice brief
这些命令会告诉您尝试了哪些 dial-peer（请搜索 pid: 关键字）以及呼叫失败的原因。
#This section will vary depending on your configuration.
#We do suggest setting the variable min-se which controls session timeout to 900 seconds.
voice rtp send-recv
voice service voip
!
allow-connections sip to sip
sip
min-se 900
!
voice class codec 711 codec preference 1 g711ulaw
codec preference 2 g711alaw
!
voice class codec 729
codec preference 1 g729r8 bytes 40
codec preference 2 g729br8 bytes 40
!
voice class codec 700
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8 bytes 40
codec preference 4 g729br8 bytes 40
!
! We support E164 format only. US/CA numbers have to be dialed in full 11 digit format.
! Use this template if you wish to convert from 7 or 10 to 11 digits.
! Replace NPA with your local area code when using 7 digit numbers
!
! translation rule definition below
!
voice translation-rule 1 rule 1 /^9\(1[2-9]..[2-9]......\)$/ /\1/ ! send out if using 9 dial-out prefix and 11 digit format ; strip 9 rule 2 /^9\([2-9]......\)$/ /1NPA\1/ ! send out if using 9 dial-out prefix and 10 digit format ; strip 9 and 1 country code rule 3 /^\(.......\)$/ /1NPA\1/ ! 7 digit format, add 1 and the "NPA" and send out (don't forget to replace NPA with your local prefix)
rule 4 /^011\(.*)$/ /1\1/ ! strip 011, send call out
rule 5 /^00\(.*)$/ /1\1/ ! strip 00 , send call out
!
! translation profile using the translation rules above
!
voice translation-profile multitel
translate called 1
!
! Outbound dial-peer definition
!
dial-peer voice 1 voip
permission term
description Termination towards MultiTEL translation-profile outgoing multitel destination-pattern .T ! or replace with 1[2-9]..[2-9]......T if only sending US calls session protocol sipv2 session target dns:sbc-us.multitel.net ! -- replace here with the SBC which is closest to you
session transport udp ! or "tcp", depending how your account is configured on MultiTEL
voice-class codec 711 dtmf-relay rtp-nte no vad
!
! Inbound dial-peer definition
!
dial-peer voice 2 voip
permission orig
description Origination from MultiTEL
huntstop
session transport udp ! or "tcp", depending how your account is configured on MultiTEL
incoming called-number .T
dtmf-relay rtp-nte
voice-class codec 711
fax-relay ecm disable
fax-rate 9600
fax protocol t38 ls-redundancy 1 hs-redundancy 1 fallback pass-through g711ulaw
no vad
!
!
! IMPORTANT: please make sure you DO HAVE the below config for security purposes
! this will allow calls to your gateway only from authorized IP addresses
voice source-group myawesomecompany
access-list 99
disconnect-cause call-reject
! add here inbound translation profile if you need to
!
! access-list definition - list here your IP addresses
! default action is deny
!
access-list 99 permit 192.168.1.0 0.0.0.255
! You may have to add MultiTEL's origination IP addresses here to allow inbound DID/origination calls from MultiTEL
! Please consult the article below for complete (and usually up to date) list of IP addresses we use to send DID/origination calls
! https://multitel.net/docs/view/161/knowledgebase/
! Sample entries below:
access-list 99 permit X.Y.Z.0 0.0.0.255
access-list 99 permit A.B.C.0 0.0.0.255